| Titre : | Investigation of Copper Oxide-Based Solar Cells |
| Auteurs : | Razika HOUILI, Auteur ; Amjad Meftah, Directeur de thèse |
| Type de document : | Mémoire magistere |
| Editeur : | Biskra [Algérie] : Faculté des Sciences Exactes et des Sciences de la Nature et de la Vie, Université Mohamed Khider, 2026 |
| Format : | 1 vol.(P108) / ill.couv.ill.en coul / 24cm |
| Langues: | Anglais |
| Mots-clés: | Copper oxide ; Solar cell ; Numerical Simulation ; Optimization |
| Résumé : |
This dissertation presents a comprehensive numerical investigation and optimization of copper oxide-based thin-film solar cells. Utilizing the Solis-1D simulation platform, three heterojunction architectures—ZnO/CdS/CuO (structure a), ZnO/CdS/Cu2O (structure b), and a multi-absorber bilayer ZnO/CdS/Cu2O/CuO (structure c)—were systematically analyzed under AM1.5G illumination.Initial unoptimized evaluations yielded a short-circuit current density of Jsc = 0.026226A/cm2 ,a fill factor of FF = 79.275% , a relatively low open-circuit voltage of Voc = 0.854V , and a conversion efficiency of Eff = 17.90% for structure (a). Structure (b) exhibited a much higher voltage (Voc = 1.715V) but its efficiency was limited to 17.12% with a reduced fill factor of 46.033%. Structure (c) achieved an efficiency of 17.89 % while retaining a high operating voltage of 1.703 V. The optimal thicknesses were established at 0.01 μm for ZnO and 0.1 μm for CdS. Increasing the absorber thickness from 0.1 μm up to 1.5 μm led to optimal efficiencies of 21.19%, 27.43%, and 27.59 % for structures (a), (b), and (c), respectively. Combining optimized thickness and doping variables yielded low-defect efficiencies of 22.09 % for structure (a), 27.42% for structures (b) and (c). Finally, introducing interface traps of 1013cm−2 within an ultra-thin interfacial layer reduced the optimized efficiencies to 8.255% for structure (a) and 14.52 % for structures (b) and (c). Elevating the bulk trap density to 5 × 1016cm−3further reduced the performance to 10.77% for the Cu2O-based designs, while the CuO single-junction performance dropped to 6.412% due to severe charge leakage. The simulation establishes that restricting bulk defects to ∼ 1015cm−3and interface states below 1011cm−2restores stable device performance to a 15.51%–17.93% range for structure (a). |
| Sommaire : |
Dedication --------------------------------------------------------------------------------------------------- I Acknowledgement ---------------------------------------------------------------------------------------- II Abstract ---------------------------------------------------------------------------------------------------- III Table of contents ----------------------------------------------------------------------------------------- IV List of figures -------------------------------------------------------------------------------------------- VII List of tables --------------------------------------------------------------------------------------------- XV General introduction --------------------------------------------------------------------------------------- 2 Chapter I: ---------------------------------------------------------------------------------------------------- 8 Fundamentals of PhotovoltaicConversion and Solar Cells ------------------------------------------- 9 I.1. Introduction to Solar Energy ---------------------------------------------------------------- 9 I.2. Principles of Photovoltaic Conversion ---------------------------------------------------- 9 I.2.1. Solar Photovoltaic Cell ------------------------------------------------------------ 10 I.2.2. Generation of Electron–Hole Pairs ---------------------------------------------- 10 I.2.3. Photovoltaic Effect----------------------------------------------------------------- 11 I.3. Classification of Solar Cells -------------------------------------------------------------- 12 I.3.1. First-generation --------------------------------------------------------------------- 12 I.3.2. Second generation ------------------------------------------------------------------ 13 I.3.3. Third Generation ------------------------------------------------------------------- 16 I.3.4. Fourth-generation ------------------------------------------------------------------ 21 I.4 . Emerging Materials and Technologies -------------------------------------------------- 24 I.5. Performance Parameters of Solar Cells ------------------------------------------------- 33 I.5.1. Electrical parameter of solar cells ----------------------------------------------- 33 I.5.2. External Quantum Efficiency (EQE) -------------------------------------------- 35 I.6 . Conclusion----------------------------------------------------------------------------------- 35 I.7. References ----------------------------------------------------------------------------------- 36 Chapter II: ------------------------------------------------------------------------------------------------- 39 Copper Oxide Materials and Their Application in Solar Cells ------------------------------------ 39 II.1. Introduction --------------------------------------------------------------------------------- 40 II.2. Structure, electrical properties and doping of Cupric oxide (CuO) ----------------- 40 II.3. Structure, electrical properties and doping of Cuprous oxide (Cu2O) -------------- 43 II.4. Synthesis and Characterization Techniques -------------------------------------------- 45 II.4.1. Synthesis methods:----------------------------------------------------------------- 45 II.4.2. Characterization techniques ------------------------------------------------------ 48 II.5. Advantages and Limitations of CuO/Cu2O in photovoltaics --------------------------- 50 II.5.1. Advantages: ------------------------------------------------------------------------- 50 II.5.2. Limitations: ------------------------------------------------------------------------- 51 II.6. Review of Copper Oxide-Based Solar Cell Architectures ------------------------------ 51 II.6.1. Homojunction and Heterojunction Designs : ------------------------------------- 51 II.6.2. Experimental and Simulation Studies in Literature : ------------------------- 54 II.7. Conclusion ------------------------------------------------------------------------------------- 54 II.8. References ------------------------------------------------------------------------------------- 56 Chapter III: Investigation of Copper Oxide-Based Solar Cells Using Solis-1D ---------------- 61 III.1. Introduction --------------------------------------------------------------------------------- 62 III.2. Solis-1D Simulation Software ------------------------------------------------------------ 62 III.3. Investigation of Copper Oxide-Based Solar Cells Using Solis-1D ----------------- 62 III.3.1. Description of the studied Structures ---------------------------------------------- 63 III.3.2. Results and discussions ------------------------------------------------------------- 65 III.3.2.1 Effect of thickness variation on the photovoltaic output parameters of the solar cells------------------------------------------------------------------------------------71 III.3.2.2 Effect of doping variation on the photovoltaic output parameters of the solar cell----------------------------------------------------------84 III.3.2.3 Optimized structures and interface /bulk trap density effect-----------------100 III.4. Conclusion---------------------------------------------------------------------------------- 102 III.5. References ---------------------------------------------------------------------------------- 104 General conclusion -------------------------------------------------------------------------------------- 105 Appendix ------------------------------------------------------------------------------------------------- 105 106 108 |
Disponibilité (1)
| Cote | Support | Localisation | Statut |
|---|---|---|---|
| MPHY/693 | Mémoire master | bibliothèque sciences exactes | Consultable |




