| Titre : | Optimization of elaboration conditions of ZnO thin films elaborated by sol-gel method |
| Auteurs : | Chaima MERIDJA, Auteur ; Louiza Arab , Directeur de thèse |
| Type de document : | Mémoire magistere |
| Editeur : | Biskra [Algérie] : Faculté des Sciences Exactes et des Sciences de la Nature et de la Vie, Université Mohamed Khider, 2026 |
| Format : | 1 vol.(P76) / ill.couv.ill.en coul / 24cm |
| Langues: | Anglais |
| Mots-clés: | Sol-gel, ZnO thin films, Spin-coating, number of layers. |
| Résumé : |
Optimization of elaborated conditions of ZnO thin films elaborated by sol-gel method This dissertation investigates zinc oxide (ZnO) thin films prepared on glass substrates by the sol–gel spin-coating technique, with a focus on the influence of the number of deposited layers on their structural, optical, and electrical properties. X-ray diffraction results show that all films crystallize in the hexagonal wurtzite phase with a polycrystalline nature, and that an intermediate number of layers (around seven) leads to improved crystallinity, larger crystallite size, and reduced defect density compared to thinner or thicker films. UV–Vis measurements reveal high transmittance (80–90%) in the visible region and an optical band gap in the range 3.22–3.27 eV, with lower Urbach energy at the optimal thickness, indicating decreased structural disorder. Four-point probe measurements demonstrate that the same thickness range also yields the lowest resistivity and highest conductivity, while additional layers strongly degrade electrical performance due to increased grain boundaries and internal stresses. These results confirm that controlling the number of layers is a key parameter for optimizing sol–gel derived ZnO thin films for transparent conducting and optoelectronic applications. |
| Sommaire : |
CHAPTER I : Bibliographic research.
I.1. Introduction 6 I.2. Transparent conductive oxides (TCOs) 7 I.2.1. Properties of TCOs 8 I.2.1.1. Electrical and optical properties of TCOs 8 I.3. The Zinc Oxide 9 I.3.1. Properties ZnO 10 I.3.1.1. Crystal structure and lattice parameters: 10 I.3.1.2. Electrical properties 12 I.3.1.3. Optical properties 12 I.3.1.4. Mechanical properties I.3.1.5. The electronic properties 15 I.4. Thin films 16 I.4.1. Properties of thin films 16 a-Structural properties 17 b-Optical properties 17 c-Electrical properties 17 d-Mechanical Properties 17 I.4.2. Factors Influencing the Quality of Thin Films 17 I.5. ZnO applications 17 References 01 19 CHAPTER II: Elaboration Methods and characterization techniques. II.1. Introduction 24 II.2. Deposition methods of thin films 24 II.2.1. Choice of a deposition technique 24 II.2.2. Physical vapordeposition (PVD) 24 II.2.2.1. Pulsed Laser Deposition (PLD) 26 II.2.2.2. PVD Sputtering 27 II.2.3. Chemical process 28 II.2.3.1. Chemical vapor deposition (CVD) 28 II.2.3.2. Sol-gel 29 II.2.3.2.1. Advantages and Disadvantages of the sol-gel process 31 a-Advantages of the sol-gel process: 31 b-Disadvantages of the sol-gel process 31 II.2.3.2.2. Deposition methods of sol-gel method 31 a-Dip-coating 32 b-spin coating 32 II.2.3.2.3. Adventages and disadventages of spin coating method 34 a- Advantages 34 b-Disadvantages 34 II.3. Characterization methods of ZnO thin films 35 II.3.1. Structural Characterization II.3.1.1. Determination of the interreticular distances and the cell parameters 37 II.3.1.2. Determination of the crystallite size 37 II.3.1.3. Determination of strain 38 II.3.2. Optical characterization UV-Visibl 38 II.3.2.1. Band gap energy 39 II.3.2.2. Urbach energy U00 40 II.3.2.3. Refractive index 42 II.3.3. Electrical characterization (four points probes method) 42 References 02 44 CHAPTER III: Experimental part: elaboration, results, and discussion. III.1. Introduction 50 III.2. Elaboration of ZnO thin films 50 III.2.1. The choice of substrate 50 III.2.2. Cleaning and preparation of substrate 50 III. 2.3. The solution’s preparation 51 III.3. Thin films deposition 53 III.3.1. Spin coating 53 III.3.2. Adhesion test 53 III.4. Results and discussion 55 III.4.1. Structural characterization with XRD 55 III.4.1.1. XRD analyses 55 III.4.1.2. Variation of the crystallite size with the number of layers. 60 III.4.1.3 The variation of interreticular distances and the cell parameters a and c with the number of layers. 63 III.4.2. Optical characterization III.4.2.1. Transmittance 65 III.4.2.2. Band gap and Urbach energy 66 III.4.2.2.1. Band gap 66 III.4.2.2.2. Urbach energy 68 III.4.2.3. Refractive index 70 III.5. Electrical characterization 70 III.5.1. The four-point characteristics 70 References 03 73 General conclusion 76 |
Disponibilité (1)
| Cote | Support | Localisation | Statut |
|---|---|---|---|
| MPHY/679 | Mémoire master | bibliothèque sciences exactes | Consultable |




